Updated November 2026. Track bodywork gets expensive in a hurry if you start with the parts that look biggest. On the CFMOTO 675SR-R, three small pieces change the silhouette of the bike for less than a single painted side panel, and two of them are bolt-on parts you can fit in a garage with hand tools.
This is the order we would buy them in, based on what each part actually does on the bike, what finishes are live in the store right now, and where the money stops being worth it.
What should you know about start with the cheapest part that changes the most?
On the CF 675SR-R, the lower chin fairing is the least glamorous item on the list and usually the first one worth buying. It closes the gap under the nose that the stock bike leaves open, which is why the front end reads as unfinished once you notice it.
Ours is matte black only, and the listing describes it as a bolt-on part with no modification required.
Because there is only one finish, there is no colour decision to get wrong. Matte black also survives track use better than gloss: it hides scuffs from tyre warmers, stands and the occasional gravel trap.
If the nose is already damaged, the side panel is the piece to price next. It comes in gloss black, matte black, gray or white, and it is the panel the winglet mounts to, so replacing both at once saves a second disassembly.
Racing winglet for the CFMOTO 675SR-R. Listed in Gloss Black, Matte Black, White and Carbon Fiber Hydro Dip.
From $89.00
What should you know about then the winglet, if you want the aero look?
Our CF 675SR-R racing winglet is listed in gloss black or matte black, with white and carbon fiber hydro dip priced higher. It mounts at the panel edge and adds the race-bike profile most riders are actually chasing.
The listing is careful about one thing, and we are too: it is a styling part, not a measured downforce or lap-time claim.
Two practical notes. Hydro dip is a dipped finish over the same base part, so it looks like carbon without being a carbon layup, and it is the most expensive finish of the four. And if you later add a V4 side winglet, check both parts against the same panel before ordering, because they occupy the same area of the fairing.
What should you know about finish with the seat cowl, once the front looks right?
On the CF 675SR-R, the seat cowl is the piece that makes the tail read as a single-seat race unit rather than a road bike with a pillion pad. Ours comes in black, white or gray and is described as an aftermarket direct-fit for the 675SR-R rear with a bolt-on replacement and no modification required.
It is the most expensive of the three and the one where fitment deserves the most attention, because the tail section is where aftermarket panels most often need persuasion. Confirm your year and tail configuration against the listing before you order, and keep the stock seat hardware until the cowl is on.
Seat cowl for the CFMOTO 675SR-R. Listed in Black, White and Gray.
$269.00
What we would skip first?
On the CF 675SR-R, skip the full painted fairing set until the small parts are done. A complete set costs many times what these three pieces cost, it is the part most likely to be damaged in a low-side, and it makes the bike harder to sell later if the colour is not stock.
Buy the pieces that change the shape, not the pieces that change the paint.
Also skip anything that promises performance numbers. Winglets on a road-derived 675 are styling and stability-feel parts; the listings say so, and any seller quoting lap-time gains for a bolt-on winglet is telling you something they cannot prove.
How do you install the CFMOTO track bodywork on budget?
On the CF 675SR-R, work on a warm day or warm the panels slightly before fitting; cold paint and cold plastic crack at the tabs. Test-fit every part before removing any protective film. Keep the original fasteners labelled by position; they are not interchangeable between the chin fairing and the side panels.
- Check clearance at full fork compression after fitting the chin fairing.
CFMOTO 675SR-R Lower Chin Fairing
Lower chin fairing for the CFMOTO 675SR-R. Listed in Matte Black.
$69.00
Which order makes sense?
On the CF 675SR-R, chin fairing first, winglet second, seat cowl third. That sequence gets the front of the bike looking finished for a small outlay, and it leaves the expensive decisions until you know how the bike is actually being used.
What should you know about parts in this guide, with live prices?
CFMOTO CF 675SR-R Lower Chin Fairing — matte black only. CFMOTO 675SR-R Racing Winglet — four finishes. CFMOTO 675SR-R Seat Cowl — black, white or gray.
| Dimension | Notes |
|---|---|
| Platform | CF 675SR-R |
| Part | CFMOTO track bodywork on budget |
| Install | Bolt-on where the listing says the stock points are reused. This guide does not add a torque sheet. |
| Use | Track-day look. Street use is called out where the part is a poor daily choice. |
| Shop | https://isleparts.com/products/cfmoto-675sr-r-racing-winglet |
What are the common questions?
On the CF 675SR-R, these are the usual questions. Will these parts fit my 675SS? Is the carbon fiber hydro dip real carbon? Do I need to remove the fairing to fit the winglet? Can I fit the seat cowl and keep the passenger seat?
Will these parts fit my 675SS?
The 675SS is the US-market name for the same platform, and our 675SR-R listings note the connection. Confirm the model year and the specific panel before ordering, as always.
Is the carbon fiber hydro dip real carbon?
No. It is a dipped finish applied to the same base part. It looks like carbon and costs more than gloss black, but it is not a carbon fiber layup.
Do I need to remove the fairing to fit the winglet?
The winglet mounts at the panel edge, so plan on at least loosening the panel. The chin fairing is the easiest of the three to fit.
Can I fit the seat cowl and keep the passenger seat?
The cowl is a replacement rear cover, so check the listing for your tail configuration. If you need to swap between solo and two-up riding, plan the change rather than forcing the cowl over the passenger seat.


