Updated November 2026. The lower tail panel is the part riders discover last. It sits below the seat cowl and behind the rider's legs, it is rarely photographed, and it costs. Then someone drops the bike on its side, or takes the tail apart for a track build, and it turns out to be the piece that needs replacing.

In short:
- , single panel, 2019–2024 S1000RR.
- The underside section of the rear bodywork.
- First casualty in a low-side, because it faces the ground.
Where does the lower tail panel sit?
On the BMW S1000RR, at the back of the bike, the tail bodywork is layered. The seat cowl closes the top. The upper tail panel runs above the tail light area. The lower tail panel forms the underside section of the rear bodywork, the surface you see when you crouch beside the bike or look up under the tail.
That position explains two things. First, it collects road spray, chain fling and heat, so it ages faster than the panels you can see from standing height. Second, crash damage in a low-side often reaches it before it reaches the upper panels, because it faces the ground when the bike goes down.
What does the lower, upper and M-style change?
| Part | Where to check the price | Position |
|---|---|---|
| Lower tail panel | See the product card | Underside of the rear bodywork |
| Upper tail panel | See the product card | Above the tail light area |
| M-style lower tail panel | See the product card | M-style shaping of the lower section |
On the BMW S1000RR, note that the M-style lower panel is cheaper than the standard lower panel, and theM-style upper panelIs more than the standard upper. The prices cross over between the two families.
If you are replacing one panel and want the M-style look, check the price of each piece individually rather than assuming one family costs more.
When the lower panel needs replacing?
- Gravel rash underneath the tail. Deep scratches that catch a fingernail will not polish out of carbon.
- Cracks around fastener holes. These spread. A cracked hole becomes a missing corner within a season.
- Delamination or whitened edges. Once water gets under the clear coat, the panel keeps getting worse.
- Heat discolouration near the exhaust or under-seat area. Cosmetic, but it rarely improves.
On the BMW S1000RR, if the damage is a light scuff in a hidden area, it is fair to leave it. Nobody sees it, and the money may be better spent elsewhere. If the panel has lost a mounting point, replace it: a lower panel that is only half attached will flap and take the neighbouring panels with it.
What should you check before ordering?
On the BMW S1000RR, get under the tail with a light and photograph the panel from below, straight on. Identify every fastener and note whether the mounting points are intact. Confirm your model year. Every panel in this range is listed for the 2019-2024 S1000RR; the 2025 bike is a different generation.
- Check the part number or shape against your existing panel if you have it off the bike.
How do you install the lower tail panel?
On the BMW S1000RR, the lower tail panel is one of the more awkward parts to fit because access is poor and it meets several other panels.
- Work with the rear of the bike supported and the wheel clear if your procedure needs it.
- Remove the seat and the cowl first; the lower panel is trapped by what sits above it.
- Watch for wiring and the tail light connector. Do not let anything hang.
- Dry-fit and check the gap along the tail light edge, which is the most visible joint even on a lower panel.
- Start fasteners by hand and stop at snug. Use your service literature for torque values.

What should you know about budget note?
On the BMW S1000RR, a lower tail panel is a lot of money for a part most people never see. If the tail is otherwise intact, replace the damaged piece and leave the rest. If you are already buying a seat cowl or upper tail panel, price the group together: the total matters more than any single line.
The full five-piece standard tail is — see thetail options guide for the breakdown.
What are the common questions?
On the BMW S1000RR, these are the usual questions. Is this the same as the upper tail panel? Why is the M-style lower panel cheaper? Can I fit the lower panel without removing the cowl? Will it fit a 2025 S1000RR? Does the exhaust heat affect it?
Is this the same as the upper tail panel?
No. The lower panel sits underneath the rear bodywork; the upper tail panel sits above the tail light area. They are separate parts with separate prices.
Why is the M-style lower panel cheaper?
It is less than the standard lower panel. The lower and upper families are priced differently, so check each piece.
Can I fit the lower panel without removing the cowl?
Usually not. The cowl and seat sit above it and block access. Plan to remove them first.
Will it fit a 2025 S1000RR?
No. These panels are listed for 2019-2024.
Does the exhaust heat affect it?
It sits in the heat path on some exhaust configurations. Discolouration near the exit is cosmetic in carbon's clear coat, but persistent heat worth checking is a mounting issue, not a finish issue.
See the Lower tail panel, the Upper tail panel and the M-style lower tail panel, or browse the full BMW S1000RR carbon range.