Updated November 2026. Direct answer:They change different halves of your body position, so the honest answer is that neither one wins in general. Rearsets move your feet, which changes knee angle, hip angle and how much you hang off the bike. Clip-ons move your hands, which changes wrist load, elbow bend and how much weight sits on the front. On the ZONTES 703RR both cost so the choice is about which end of you is uncomfortable, not about budget.

What does rearsets actually change?
On the ZONTES 703RR, rearsets relocate the footpegs and, on an adjustable set, the lever tips. Moving the pegs back and up closes your knee angle, opens your hip slightly, and raises your feet away from the road. On track that buys ground clearance.
On the road it usually means a more folded leg and a firmer push into the tank under braking.
What they do not do is change your reach to the bars. If your wrists hurt on a long ride, rearsets will not fix it, and if anything a more rearward peg position can put slightly more weight through your arms.
What does clip-ons actually change?
On the ZONTES 703RR, clip-ons replace the handlebar with two separate bars clamped to the fork legs, usually through a new top triple clamp. That changes bar height, sweep and pullback.
Lower bars load the front more and tuck your elbows in; higher or wider bars take weight off your wrists and make the bike easier to steer at low speed.
What they do not do is change your leg position. If your knees are cramped or your boots scrape in corners, clip-ons do nothing for either problem.
What is the two changes, side by side?
| Adjustable rearsets | Clamp + clip-ons | |
|---|---|---|
| Price on the 703RR | See the product card | See the product card |
| Moves | feet | hands |
| Fixes | cramped knees, ground clearance | wrist load, front-end weight |
| Does not touch | bar reach | leg position |
| Commuter risk | mild | higher — slow-speed control |
What does the 703RR case change?
On the ZONTES 703RR, the two options sit at the same price point, which makes the decision unusually clean:
- ZONTES 703RR Adjustable Rearsets. Four finish variants. Seven adjustment positions, documented in the listing.
- ZONTES 703RR Upper Triple Clamp & Clip-On Handlebars. Supplied as a matched clamp and bar set.
Because the price is the same, buying both at once is a decision rather than a one. That matters, because fitting both at the same time makes it hard to tell which change caused a new problem.
Which one changes the ride more?
On the ZONTES 703RR, in our experience the honest ranking depends on the complaint, not on the part:
- Numb hands, sore wrists, weight on the bars — clip-ons. This is a front-end problem and only the bars address it.
- Cramped knees, boots touching down, want more ground clearance — rearsets. Nothing at the bars will help.
- Track riding with a tucked position — rearsets first, because peg position sets your anchor on the bike. Bars come second, once your feet are planted.
- City riding and commuting — clip-ons are usually the riskier change, because lower bars make tight turns and slow-speed control harder. Rearsets are the milder change on a commuter.
There is one honest caveat: on a faired bike, both changes are partly limited by the bodywork. Lower bars can bring your hands closer to the screen or the tank at full lock. Higher pegs can bring your heels closer to the tail section. Check clearance before you commit to a radical setting.
What neither part fixes?
On the ZONTES 703RR, seat height and seat shape. If the seat is the problem, neither part solves it. Suspension setup. A harsh rear shock makes a long ride worse than bar height does, and no cockpit part compensates for it. Screen buffeting. That is a windshield and helmet question, not a control question.

What is the order we would use?
On the ZONTES 703RR, identify the pain point. Wrists or knees. Not both at once, or you will not know what worked. Change one part. Fit it, set it to a middle position, and ride at least a few hundred kilometres before adjusting again.
- Adjust in small steps. Both parts have a range for a reason. The most aggressive setting is rarely the most comfortable.
- Re-check cable, hose and bodywork clearance after every adjustment, at full steering lock and with the suspension compressed if you can.
What are the common questions?
On the ZONTES 703RR, these are the usual questions. Do I need a new top triple clamp to fit clip-ons? Are adjustable rearsets worth it on a road bike? Can I fit both at once? Which is easier to install? Do they fit the 675SR-R?
Do I need a new top triple clamp to fit clip-ons?
On the 703RR our clip-on set is supplied with an upper triple clamp as a matched pair, so you are not reusing the stock clamp. That is the safer route on a faired bike because the clamp and bar geometry are designed together.
Are adjustable rearsets worth it on a road bike?
Yes, if you have a specific complaint. The value is in the adjustment range, not in the part itself. If you fit them and never move them from the first setting, you have bought a fixed rearset at an adjustable price.
Can I fit both at once?
You can, and plenty of riders do. Just accept that if the result is wrong, you will have two variables to undo instead of one.
Which is easier to install?
Rearsets are generally the simpler job because the hydraulic lines stay put on most designs. Clip-ons involve the top clamp, the controls and often the brake and clutch lines. Neither is difficult, but the clip-on job takes longer and deserves more checking afterward.
Do they fit the 675SR-R?
No. Both listings are for the ZONTES 703RR; the CFMOTO platforms have their own clamp and clip-on.
If you want the detail on each part before deciding, read the 703RR rearset adjustment guide and the 703RR cockpit change guide. For the general principles behind bar swaps, see what actually changes when you switch to clip-ons. The rest of the platform is in the ZONTES 703RR parts collection.