Updated November 2026. A triple clamp is the pair of castings that grip your fork tubes and connect them to the steering stem. The top triple clamp is the upper one, and it does two jobs at the same time: it holds both fork legs at a fixed spacing and it carries whatever your handlebars or clip-ons bolt onto. If you are changing bar position, replacing a damaged clamp, or refreshing a tired cockpit, the top clamp is usually the part that changes.
Everything below refers to aftermarket parts, not manufacturer OEM components.
What does a triple clamp actually?
A triple clamp is a structural part, not a cosmetic cover. It sits at the front of the frame, around the steering head, and it does three jobs:
- Holds fork spacing. The upper and lower clamps grip the fork tubes so the front wheel stays centred and parallel.
- Locates the steering stem. The stem passes through the headstock bearings; the clamps keep the whole assembly square to the frame.
- Carries the controls. Bar risers, clip-on clamps, ignition brackets and some switchgear mounts bolt to the top clamp.
How do you choose between top clamp and bottom clamp?
Both clamps grip the fork tubes, but they are not interchangeable. The bottom clamp also carries the steering stem and sets the fork offset, which is part of the bike's steering geometry. The top clamp is the one that holds your bars, which is why it is the part riders change for cockpit reasons. A top clamp swap does not alter fork offset.
When an upgrade or replacement is worth it?
Replace the clamp when it is damaged or when the clamp bolts no longer hold torque. Beyond that, an upgrade makes sense in three situations:
- You are switching to clip-ons. A combined clamp and clip-on kit gives you a matched pair instead of mixing brands.
- You want a more aggressive position. Clip-ons move your hands forward and down, which loads the front end more.
- The original clamp is cosmetically finished out. A machined clamp is a visible cockpit part and a cheap way to tidy a used bike.
What should you check before you order?
Most fitment mistakes come from measuring the wrong thing. Work through this list before you buy:
- Fork tube diameter at the top clamp. Measure the tube where the clamp grips it, not the stanchion above it.
- Clamp bolt pattern and thread. Count the bolts and confirm the thread pitch matches your original hardware.
- Bar or clip-on tube diameter. If the kit includes clip-ons, confirm the bar tube size matches your grips and controls.
- Accessory mounts. Check whether your ignition switch, dash bracket or brake line guide bolts to the clamp.
- Cable and hose length at full lock. Lower bars can pull the brake line and throttle cables tight.
- Model year and market name. The US-market CFMOTO 450SR is sold as the 450SS, and the 675SR-R as the 675SS. Mounting points are the same across the model years listed on each product page, but confirm your year before ordering.

What should you know about fitment for the bikes we stock?
We list three top clamps, all aftermarket, all with the finishes shown on the product page:
- CFMOTO 450SR Top Triple Clamp + Clip-On Handlebars — Silver or Black. Fits 2023–2026 CFMOTO 450SR and the US-market 450SS, with the same mounting points across those years.
- CFMOTO 675SR-R Top Triple Clamp + Clip-On Handlebars — Black or Silver, built for the 675SR-R platform and the US-market 675SS.
- ZXMOTO 820RR Aluminum Top Triple Clamp — Black or Silver, aluminium alloy, for the ZXMOTO 820RR.
The two CFMOTO kits include the clip-on bars, so you are not hunting for a matching bar clamp afterwards. If you only want to read the install notes for the 450SR part first, our 450SR top triple clamp fitment notes go through the mounting points in more detail.
CFMOTO 450SR Top Triple Clamp + Clip-On Handlebars
Top triple clamp + clip-on handlebars for the CFMOTO 450SR. Listed in Silver and Black.
$399.00
CFMOTO 675SR-R Top Triple Clamp + Clip-On Handlebars
Top triple clamp + clip-on handlebars for the CFMOTO 675SR-R. Listed in Black and Silver.
$469.00
ZXMOTO 820RR Aluminum Top Triple Clamp
Aluminum top triple clamp for the ZXMOTO 820RR. Listed in Black and Silver.
$399.00
What does the installation change?
The swap is straightforward. The problems come from rushing the sequence.
- Support the front end first. Take the weight off the front wheel before you loosen anything.
- Loosen the clamp bolts evenly. Alternating between bolts stops the clamp cocking on the tubes.
- Slide the tubes to the same height. Measure from the top of each tube to the clamp face; an uneven pair steers differently left and right.
- Torque in stages. Snug, check alignment, then torque to the figure in your service manual.
- Check lock-to-lock clearance. Turn the bars fully each way and look for contact between the clip-ons, the tank, the fairing and the brake reservoir.
- Recheck after the first rides. New hardware settles, so confirm the clamp bolts are still at torque.
How a top clamp changes the way the bike feels?
A top clamp on its own is a mounting part; the change in feel comes from what it carries. Clip-ons put your hands further forward and lower, which shifts weight onto your wrists and reduces leverage at low speed.
The trade is a more connected front end.

Before you ride, set the lever angles so your wrists sit straight, and check that the brake and clutch lines do not pull at full lock.
| Dimension | Notes |
|---|---|
| Platform | Not a single-bike fitment note. Confirm the platform on the product page. |
| Part | motorcycle triple clamp |
| Install | Not a single-part install note. Follow the sections above. |
| Use | Care, fit, or buying judgment. Not a fitment claim for one bike. |
| Shop | https://isleparts.com/products/cfmoto-450sr-top-triple-clamp-clip-on-handlebars |
What are the common questions?
Do I need a new top clamp to fit clip-ons? Will one clamp fit both the 450SR and the 450SS? How do I know I have the right fork diameter?
Do I need a new top clamp to fit clip-ons?
Not always, but usually. Many clip-on sets clamp directly to the fork tubes above the top clamp, so the original clamp must leave enough exposed tube to grip. A combined clamp and clip-on kit removes the guesswork.
Will one clamp fit both the 450SR and the 450SS?
The US-market 450SS uses the same mounting points as the 450SR for the years listed on the product page. Confirm your model year and bodywork before ordering, because clamp and fairing changes between years are the usual cause of a bad fit.
How do I know I have the right fork diameter?
Measure the fork tube where the clamp grips it, with a caliper, and compare that to the product page. Measuring higher up, where the diameter steps down, is the usual mistake.
Start with the clamp and clip-ons, then set lever angles and line routing before changing anything else. The CFMOTO 450SR / 450SS parts collection lists the matching windshields, winglets and tank cover.


