Updated November 2026. Every bodywork job ends with the same question: which of these old fasteners goes back on? The answer decides whether the panel sits flat and stays there.

In short:
- Replace any clip that has gone white at the bend.
- Replace any bolt with damaged threads or a rounded head.
- Reuse structural bolts if they are clean and undamaged, with the manual's torque.
What should you know about replace or reuse, at a glance?
| Item | Verdict | Reason |
|---|---|---|
| Plastic clips | replace | one-use tension |
| Rounded or stretched bolt | replace | next removal gets harder |
| Corroded aluminium fastener | replace | galvanic seizure |
| Clean structural bolt | reuse | torque to manual figure |
| Pliable rubber grommet | reuse | still isolates vibration |
What does the clips change?
Plastic clips are designed to be replaced. They hold tension by deforming, and once they have deformed they do not spring back. A clip that has gone white at the bend has lost that tension and will rattle — or worse, let the panel move against the next one until the paint wears through.
Clips are cheap. Panels are not. If a clip looks tired, bin it.
What does the bolts change?
Threads. Rolled or flattened threads will not hold torque, and they damage the thread they go into. Head. A rounded hex or Torx head means the next removal is harder than this one. Corrosion. White powder on aluminium fasteners in a steel insert is a galvanic problem waiting to seize.
- Length. A bolt that is too long will bottom out and crack the panel it is holding.
What should you reuse?
Well-finished structural bolts — engine mounts, clamp bolts, anything holding load — are reusable if they are clean, straight and correctly threaded. Replace them if they have been over-torqued, if the head is damaged, or if the coating is gone.
Rubber grommets and well nuts are reusable while they are still pliable. Once they harden, they stop isolating vibration and start transmitting it into the panel.

What is the parts people forget?
There are usually more fasteners than you think: two under the nose, one behind the seat, a hidden clip at the leading edge. Counting them on removal and counting them on refit is the simplest way to avoid a rattle you cannot find later.
A phone photo of the panel edge before removal costs nothing and answers most questions later, including which bolt went where.
What should you know about torque, honestly?
Our listings do not publish torque values, and this article will not invent them. Use the figures in your manual for the fastener you are installing. Where no figure exists, snug plus a quarter turn on a small bodywork fastener is a reasonable habit, and a torque wrench is better than a guess on anything structural.
What should you know about mixed metals?
Stainless bolts into aluminium threads will corrode over time. A little anti-seize on the threads costs nothing and prevents a fastener seizing in a part you cannot replace cheaply.
What is the panels these fasteners hold?
We do not sell clips or fasteners separately: the panels above are designed to reuse your stock fixings, which is why their condition decides how the new panel ends up sitting. If a clip fails in a week, the panel is the part that pays for it.
What are the common questions about fasteners?
Can I use hardware-store bolts? Should I replace all clips at once? Why does my panel rattle after refitting? Do I need threadlocker? How many clips does one panel use?
Can I use hardware-store bolts?
For non-structural trim, generally yes if the thread and length match. For anything load-bearing, use the correct specification.
Should I replace all clips at once?
Only if the panels are already off. Otherwise replace the ones that are tired.
Why does my panel rattle after refitting?
Usually a lost or tired clip, or a fastener that is loose rather than missing.
Do I need threadlocker?
On fasteners that see vibration and are not nyloc, a medium threadlocker is sensible.
How many clips does one panel use?
It varies by panel and model. Count them on removal — that count is your shopping list.
Fitting sequence: align before you tighten. Arrival checks: inspecting new panels.