Updated November 2026. Direct answer: ignore the painted side. The three reliable tells are the inside face of the panel, the sound it makes when you tap it, and the edge where it was cut or moulded. Paint, primer and a gloss clear coat can make ABS, fiberglass and carbon look identical from two metres away, and they behave completely differently when you repair them.

What does the look at the back of the panel change?
The inside face is rarely finished to the same standard as the outside, and that is exactly why it is useful.
- ABS is usually a uniform black or grey moulding with visible ejector pin marks and mould seams. There is no fibre structure because there is no fibre.
- Fiberglass shows a mat or cloth texture under the resin, often with a rougher, slightly uneven surface and visible strands where it was trimmed.
- Carbon fibre shows a weave on the inside face too, unless it is a cosmetic skin over another core. Look for a regular diagonal pattern, not a random mat.
If the back is covered in sound deadening, tape or a heavy primer, you have lost the easiest test. Move to the edge.
What does the tap test change?
Tap the panel with a fingernail or a plastic trim tool, not a metal one.
- ABS gives a dull, flat, plastic knock. It sounds like a storage box.
- Fiberglass gives a harder, drier click with a slight ring to it.
- Carbon gives the sharpest, highest-pitched tick of the three, because the panel is stiff and thin.
The tap test is comparative, not absolute. Tap two panels you already know and you will calibrate your ear in about thirty seconds. Do not use it on a heavily padded or double-skinned panel, where the sound is muffled regardless of material.
What does the edge and the cut line change?
Where a panel has been trimmed, the material shows itself.
- ABS cuts to a clean, solid edge with no visible structure. A sharp blade leaves a shaving, not dust.
- Fiberglass leaves a slightly hairy edge, and you can often see individual strands at the cut.
- Carbon shows woven layers at the cut edge. On a good panel the layers are tight and evenly stacked; on a cheap one you may see voids or dry patches.
Look at the edge inside a fastener hole as well. That is the place where a painted panel gives away what is underneath.
What is the three tests, summarised?
| Test | ABS | Fiberglass | Carbon |
|---|---|---|---|
| Inside face | smooth moulding, pin marks | mat texture, visible strands | regular diagonal weave |
| Tap sound | dull knock | dry click, slight ring | sharp high tick |
| Cut edge | solid, no structure | hairy, strands at the cut | woven layers stacked |
| Failure mode | flexes, then cracks cleanly | crazes before breaking | stiff until it cracks |
What does each material mean for repair?
This is why identification matters more than curiosity. ABS is the most repairable of the three for a home workshop. Solvent welding and heat can close a crack, and the repair can be sanded and painted. A cracked tab is often fixable with a reinforcement plate behind it.
Fiberglass is repairable too, but the repair adds material. You grind back, lay new glass, sand and refinish. The result is strong but rarely invisible unless you repaint the whole panel.
Carbon fibre is the least forgiving. A cosmetic scuff in the clear coat can be polished. A crack in the laminate is a structural repair, and a home repair that looks acceptable can leave the panel weaker at exactly the point that failed. For a load-bearing panel, replacement is usually the honest answer.
What paint hides, and what it cannot hide?
A painted carbon panel and a painted ABS panel can look the same on the bike. What separates them in the real world is weight, stiffness and how they fail. Carbon is stiffer and lighter; ABS flexes more before it cracks, then cracks cleanly; fiberglass sits between the two and tends to craze before it breaks.
That is also why a marketing phrase like carbon look means nothing. Carbon look is a finish, not a material. The guide to real carbon versus carbon look goes through the difference in detail.
What a listing should tell you?
A listing that does not name the material is telling you something. Two examples from our own range, one each way:
- Kawasaki ZX10r Carbon Fiber Front Fender. The material is in the product name because it is the point of the part.
- CFMOTO 675SR-R Side PanelFour colour variants. It is sold as a painted replacement panel, not as a carbon part, and the listing does not claim a weave.
Neither listing is better than the other. They are different products for different jobs, and the naming should make that obvious before you buy.

What are the common questions?
Can I tell carbon from fiberglass by weight? Is a magnet useful? Can painted carbon be stripped back to a visible weave? Why does my ABS panel crack at the fastener holes? Which material is best for a first aftermarket panel?
Can I tell carbon from fiberglass by weight?
Sometimes. Carbon panels are usually lighter for the same stiffness, but a light fiberglass panel and a heavy carbon panel can weigh the same. Use weight as a hint, not a test.
Is a magnet useful?
No. None of these three materials is magnetic. A magnet only helps if you are checking for steel inserts or fasteners.
Can painted carbon be stripped back to a visible weave?
Rarely worth it. The clear coat and the resin surface are part of the finish, and stripping usually damages the weave you were hoping to expose.
Why does my ABS panel crack at the fastener holes?
Usually over-tightening or a missing shoulder washer. The guide to fastener-hole cracks covers the cause and the prevention.
Which material is best for a first aftermarket panel?
For the platforms we cover, the painted panels on CFMOTO and ZXMOTO bikes are ABS-range parts priced from and carbon starts on the ZX-10R. Buy the material the part's job needs, not the most expensive name.
For how aftermarket panels compare with original equipment in general, see aftermarket versus OEM fairings. The CFMOTO 675SR-R and 675SS range is in the 675SR-R and 675SS parts collection.