Updated November 2026. Short answer: the ZXMOTO 820RR Windshield is a polycarbonate screen, not acrylic, sold in four combinations — Black or Gray, each in a Ridged or Rounded style. It is listed for the 2026 ZXMOTO 820RR and explicitly not for the 820R naked, and the 820RR-R is not confirmed. If you are replacing a cracked or yellowed screen, those two details matter more than the colour.
- Material: PC (polycarbonate) — impact-resistant, thickened and hardened, stable from -40°C to °C, flame-retardant.
- Options: Black / Ridged, Black / Rounded, Gray / Ridged, Gray / Rounded.
- Fitment: 2026 ZXMOTO 820RR only — not the 820R naked; 820RR-R unconfirmed.
- Install: compare the hole pattern against your stock screen before mounting.
Windshield for the ZXMOTO 820RR. Listed in Black and Gray; Ridged or Rounded.
$199.00
Why is the 820RR screen polycarbonate?
On the ZXMOTO 820RR, most screens at this price point are acrylic. The 820RR screen is polycarbonate, and the listing is specific about it — PC, impact-resistant, thickened and hardened, stable from -40°C to °C, and flame-retardant in the sense that it self-extinguishes when removed from a flame.
For a rider, that translates into three practical differences. Polycarbonate bends before it cracks, which matters on a track bike that gets leaned on in a paddock. It handles heat better, so a screen left in the sun or behind a hot fairing is less likely to distort. And it is more tolerant of a stone strike at speed than acrylic of the same thickness.
The trade-off is on the care side: polycarbonate is softer on the surface and scratches more easily than acrylic, so the washing routine matters. More on that below.
What does the ridged or rounded change?
On the ZXMOTO 820RR, the four variants come from two colours and two styles. Black and Gray are the colours; Ridged and Rounded are the surface treatments. The Ridged option carries vertical ridges up the face of the screen.
It reads as a more technical, race-derived shape and it breaks up reflections in a way a smooth screen does not. The Rounded option is the smoother, more conventional face. Neither is faster — this is a styling decision, and the one you pick should match the front of your bike rather than the photo you liked most.
On a black bike, Black / Ridged is the combination that looks most deliberate. On a lighter or grey bike, Gray / Rounded tends to sit more quietly. The mismatch to avoid is a black screen on a bike whose nose trim is grey — the seam at the mounting edge is where that shows.
What does the fitment change?
The listing states 2026 ZXMOTO 820RR, and it states the negative case as well: not the 820R naked, and the 820RR-R is not confirmed. That kind of note is worth reading twice, because the three names look interchangeable in a search result and are not interchangeable at the mounting points.
If your bike is an 820R naked, this screen is not the part. If it is an 820RR-R, the store has not confirmed fitment, so ask before ordering rather than assuming the fairing is the same. Send the model year and a photo of the current screen with the enquiry — it is faster than comparing part numbers and it protects you if the listing photo was shot on a different year.
How do you check the hole pattern before you mount?
On the ZXMOTO 820RR, the install note on the listing is simple: compare the hole pattern with your stock screen before mounting. Do it on a bench, not on the bike, with both screens side by side and the mounting bolts pushed through the holes.
If a bolt binds at an angle, stop — forcing it puts stress into a polycarbonate hole, and polycarbonate does not forgive a stress riser the way a metal bracket does.
- Lay both screens face down on a soft cloth and align the top edge.
- Push a bolt through each hole in turn and check it drops through without side load.
- Fit finger-tight first, in a cross pattern, and check the gap to the fairing before final torque.
- Do not overtighten. Polycarbonate creeps under a tight fastener; a rubber or nylon washer under the head spreads the load.
What should you know about height, airflow and the 820RR riding position?
The ZXMOTO 820RR is a faired, track-focused bike, and the screen's job is to move the airflow from your chest to your helmet without creating turbulence at the top edge. Where that edge sits relative to your eye line decides whether you look over the screen or through it.
Polycarbonate is optically clear enough to look through, but a screen you look through should be clean and free of scratches — which is the argument for looking after it rather than replacing it twice. If you ride mostly upright in traffic, the top edge will sit lower in your vision and the screen becomes a wind deflector rather than a visor.
What does the care change?
On the ZXMOTO 820RR, polycarbonate is stable across the temperature range the listing quotes, but it is not solvent-resistant. Petrol, brake cleaner, acetone and ammonia-based glass cleaners will haze it. Wash with water and pH-neutral shampoo, rinse thoroughly before wiping, and use a clean microfibre cloth.
Dry wiping dust is how most screens get their fine scratches.
Keep polish abrasive-free and plastic-specific. If the screen carries a coating, an abrasive compound will take it off in a patch that shows at an angle even when the screen looks clean.
Which listed parts does this guide cover?
- ZXMOTO 820RR Windshield — Black / Ridged, Black / Rounded, Gray / Ridged, Gray / Rounded — PC, 2026 820RR.
On the ZXMOTO 820RR, material and fitment notes were checked against the live ISLEPARTS product page on 4 November 2026; the card price comes from that page. For the rest of the bike, see the ZXMOTO 820RR Parts collection, the 820RR winglet guide and the 820RR fuel cap guide.
| Dimension | Notes |
|---|---|
| Platform | ZXMOTO 820RR |
| Part | windshield |
| Install | Confirm the steps on the product page before you order. This guide does not add a torque sheet. |
| Use | Track-day look. Street use is called out where the part is a poor daily choice. |
| Shop | https://isleparts.com/products/zxmoto-820rr-windshield |
What are the common questions?
On the ZXMOTO 820RR, these are the usual questions. Is this screen acrylic or polycarbonate? Will it fit the 820R naked? Can I fit it with the stock bolts? Does the Ridged style affect airflow?
Is this screen acrylic or polycarbonate?
Polycarbonate. The listing states PC explicitly and notes it is not acrylic — the two materials need different cleaning products.
Will it fit the 820R naked?
No. The listing states 2026 ZXMOTO 820RR and explicitly excludes the 820R naked. The 820RR-R is not confirmed.
Can I fit it with the stock bolts?
Plan to reuse the stock fasteners and check each hole on a bench first. A nylon or rubber washer under the head is cheap insurance against stress at the hole.
Does the Ridged style affect airflow?
The listing presents Ridged and Rounded as surface styles rather than different aerodynamic profiles. Treat the choice as cosmetic.
