Updated November 2026. Most parts questions come down to vocabulary. A rider asks for a belly pan and means a chin fairing, or asks for a cowl and gets a seat cover. This glossary defines the terms we use in every listing and article, grouped by what the part does, with a real example and price for each so the words connect to something you can look at.
What should you know about panels that cover the bike?
What should you know about fairing? What should you know about side panel? What should you know about belly pan? What should you know about chin fairing? What should you know about tank cover? What should you know about seat cowl?
What should you know about fairing?
The outer body shell. On a sportbike it means the panels around the engine, radiator and nose. There is no single fairing on most bikes: a side is usually two or three panels that meet along a seam.
What should you know about side panel?
The large panel between the front wheel and the tail, covering the radiator and the middle of the engine. Prices vary widely by platform: on the 675SR-R, for the ZX-10R pair.
What should you know about belly pan?
The panel under the engine, sometimes called a lower fairing. It is the part most likely to be damaged by a kerb or a paddock stand. The ZX-10R carbon belly pan is.
What should you know about chin fairing?
A small lower nose piece that sits under the radiator, smaller than a belly pan. Ours is the 675SR-R lower chin fairing, the cheapest part in the catalogue.
What should you know about tank cover?
A shell that fits over the fuel tank, either half-wrap (covering the sides and top) or full. It changes the colour of the largest visible surface on the bike without painting the tank. The 450SR half-wrap is; the ZONTES 703RR racing tank cover is.
What should you know about seat cowl?
A cover that replaces the pillion seat, giving the tail a single-seat shape. Prices run from on the 500RR and 820RR to on the S1000RR.
What should you know about tail panel?
The rear bodywork behind the seat. On the S1000RR the range splits into an upper tail panel a lower tail panel and tail side panels per pair, because the tail is built from several parts.
What should you know about short tail?
A shortened tail section that removes the overhang behind the seat. Ours is the ZXMOTO 500RR short tail, available in fixed and foldable versions.
What should you know about shark fin?
A vertical panel that fills the triangular gap between the side panel and the tail. It is a shape part rather than a protective one. The 675SR-R shark fin side panel is.
What should you know about hugger?
A close-fitting rear fender that follows the tyre. It keeps spray and debris off the shock. The S1000RR carbon rear hugger is.
What should you know about heel guard?
A plate at the footpeg area that stops your boot rubbing the frame or exhaust. The ZX-10R pair is; the S1000RR pair is.
What should you know about inner panel?
The panel you only see with the fairing off, covering the airbox or radiator sides. Easy to skip, and the reason some bikes look unfinished with the bodywork removed.
What should you know about frame cover, swingarm cover, subframe cover?
Protective shells that sit over structural parts. The ZX-10R swingarm covers are for the pair. These are visual parts first and protection second.
What should you know about aero and screens?
What should you know about windshield / windshield? What should you know about winglet? What should you know about mirror block-off plate?
What should you know about windshield / windshield?
Both spellings are used for the same part. Screens are described by height (stock, tall), tint (clear, smoke, black) and shape (race, touring, ridged, rounded).
What should you know about winglet?
A fin mounted on the side of the nose, either for downforce or for looks. In our catalogue winglets run from for the 675SR-R racing winglet to for the S1000RR carbon pair.
What should you know about mirror block-off plate?
A plate that covers the mirror mounting holes when mirrors are removed, usually for track use. Ours are plain and with an LED turn signal.
What should you know about cockpit and controls?
What should you know about triple clamp? What should you know about clip-ons? What should you know about rearsets? What should you know about raised footpegs?
What should you know about triple clamp?
The bracket that holds the fork tubes and the handlebars, also called a top yoke. Replacing it is how most riders change bar height and angle.
What should you know about clip-ons?
Two separate handlebars that clamp directly to the fork tubes, replacing a single bar. They lower and narrow the riding position.
What should you know about rearsets?
Adjustable footpeg and lever assemblies that move your feet back and up. The ZONTES 703RR rearsets are and have multiple mounting positions.
What should you know about raised footpegs?
Footpegs that sit higher than stock without changing the levers, cheaper than full rearsets. The 820RR raised footpegs are.
What should you know about materials and finishes?
What should you know about ABS? What should you know about polycarbonate? What should you know about dry carbon and wet carbon? What should you know about 3K weave? What should you know about hydro dip?
What should you know about ABS?
The plastic most painted motorcycle panels are made from. It flexes, takes paint well and is repairable.
What should you know about polycarbonate?
A transparent plastic used for screens. It resists impact better than acrylic, which is why screens bend rather than shatter. Check the listing rather than assuming every screen is the same material.
What should you know about dry carbon and wet carbon?
Dry carbon is laid up in a mould under vacuum with a precise resin content, giving a lighter, more consistent part with a visible weave. Wet carbon is hand-laid, heavier and more variable.
What should you know about 3K weave?
The common carbon cloth pattern, where filaments form each tow. It describes the look of the weave, not the strength of the part.
What should you know about hydro dip?
A printed film applied to a plastic part to imitate carbon weave. It looks like carbon and is not carbon. Some catalogue parts are priced differently for a hydro dip finish, which is the clue.
How do you use the terms?
The safest habit is to match the part name to the drawing in the listing rather than to the word. If you are browsing by bike instead, the S1000RR carbon collection shows how many separate parts make up one fairing side, which is the fastest way to learn the vocabulary.
| Dimension | Notes |
|---|---|
| Platform | Kawasaki ZX-10R, CF 675SR-R. A part for one of these bikes does not fit the others. |
| Part | motorcycle bodywork glossary |
| Install | Confirm the steps on the product page before you order. This guide does not add a torque sheet. |
| Use | Track-day look. Street use is called out where the part is a poor daily choice. |
| Shop | https://isleparts.com/collections |
What are the common questions?
Is a seat cowl the same as a tail panel? What is the difference between a belly pan and a lower fairing? Does a tank cover replace the tank?
Is a seat cowl the same as a tail panel?
No. A seat cowl covers the pillion seat area only. A tail panel is the bodywork around and behind it. On some bikes you need both to change the whole rear.
What is the difference between a belly pan and a lower fairing?
Usually nothing. Both describe the panel under the engine. A chin fairing is the smaller version at the front.
Does a tank cover replace the tank?
No. It fits over the existing tank. Nothing in the catalogue replaces a fuel tank.