Updated November 2026. Direct answer:Polishing is worth trying on fine swirl marks and light scuffing. It is usually a waste of time on anything your fingernail catches, and it is the wrong answer entirely once the screen has started to craze or crack. On a screen that costs to to replace, a polishing kit plus an afternoon often costs more than the part.

What should you know about first, decide what you are looking at?
- Swirl marks are shallow, wide and only visible at an angle in sunlight or under a forecourt light. They do not catch a fingernail.
- Scratches are narrow lines. If your fingernail drops into the line, the damage is below the surface coating.
- Crazing looks like a fine spiderweb inside the material, usually near mounting holes or along a bend. It is not a surface defect at all.
- Cracks start at holes, edges or the centre of a bend and grow. A cracked screen is finished, regardless of how small the crack looks.
Crazing and cracks are structural. No polish touches them, and a screen that has crazed around the mounting holes can fail completely at speed.
What should you know about damage and the decision?
| Damage | Fingernail catches? | Verdict |
|---|---|---|
| Swirl marks | no | polish carefully or live with it |
| Light scuff | no | polish, expect it to return |
| Deep scratch | yes | replace |
| Crazing | inside the material | replace immediately |
| Crack | See the product card | replace, do not ride on it |
What does polishing actually?
Most motorcycle screens are a thermoplastic with a hard coat applied over the surface. That coating is what resists UV and light abrasion, and it is also what you remove first when you polish. So a polished screen can look better for a while and then degrade faster than before, because the coating that was protecting it is gone.
This is the part polishing guides tend to skip.
- Fine swirls: a careful hand polish with a plastic-safe compound can improve them, with the coating trade-off above.
- Light scuffs from a glove or a cover: often improve, and often come back.
- Deep scratches: you will chase them, thin the material, and still see them at night.
- Crazing or cracks: not a polishing problem. Replace.
Never use an ammonia-based cleaner or an abrasive household cream on a screen. Both attack the surface, and the damage shows up as a permanent haze. The cleaning guide covers what is safe.
When replacement is the cheaper answer?
Do the arithmetic before you start. A polishing compound, a foam pad and two hours of your time is a real cost. Against that:
- Yamaha XMAX 300 Front WindshieldFrom.
- ZXMOTO 820RR WindshieldFour variants.
- CFMOTO 675SR-R Split Racing WindshieldIn eight finishes.
If your screen is over five years old, has any crazing, or has a scratch you can feel, replacement is usually the better decision. You also get a clean surface with an intact coating, which is what keeps the next three years of cleaning from making the problem worse.
What is the night test?
Before you decide, ride at night on an unlit road. Scratches that are invisible in daylight scatter oncoming headlights into a haze, and that haze sits exactly where you need to see. A screen that fails the night test is not a cosmetic issue.
This is also why a polished screen can disappoint: the surface may look better in the garage and still scatter light badly at night, because the deep damage is still there.
What should you know about prevention that actually works?
Wash the screen separately from the rest of the bike, with its own cloth. Grit from the fairing lower down will scratch the screen. Soak before wiping. Bugs and road film soften in water; dry wiping grinds them in. Never use a dry paper towel. Paper is abrasive enough to haze a screen over a season.
- Watch the cover. A gritty bike cover is one of the most common causes of fine swirls across the whole screen — the cover rules matter here.
What are the common questions?
Can I polish a polycarbonate screen? Will a polishing kit remove a deep scratch? Is a cracked screen repairable? How do I choose between clear, smoke and black if I am replacing? What should you know about a carbon screen?
Can I polish a polycarbonate screen?
You can, but you will remove part of the hard coat. Do it only for light damage, and expect the polished area to age faster than the rest.
Will a polishing kit remove a deep scratch?
No. It will reduce the edges and make the scratch less visible in daylight, but it cannot restore the missing material.
Is a cracked screen repairable?
Treat it as a replacement. A screen carries wind load at speed, and a repair around a mounting hole is not a safe place to save money.
How do I choose between clear, smoke and black if I am replacing?
That is a visibility question more than a styling one, and the tint comparison covers it. Everything we stock for the 820RR is in the ZXMOTO 820RR parts collection.
What should you know about a carbon screen?
It is opaque and has a clear coat, not a hard-coated plastic surface — different care rules, covered in the carbon care guide.