Updated November 2026. Both BMW S1000RR tank side panel options in this catalogue cost. That makes part of the decision easy and part of it harder: you are not comparing prices, you are working out which panel shape your bike actually needs. One is full-coverage. The other has cutouts.

In short:
- Full-coverage: continuous carbon surface across the tank flank.
- With cutouts: openings for the hardware that lives there.
- Same price, same year range — the shape decides, not the budget.
What both panels share?
- Carbon fibre construction, listed for the 2019-2024 S1000RR.
- The same price: each.
- A single default variant, so there is no finish choice to make.
- The same position on the bike: the tank flank, below the tank cover and behind the front bodywork.
On the BMW S1000RR, because the price and finish match, everything comes down to coverage and access.
What should you know about full-coverage tank side panels?
On the BMW S1000RR, the full-coverage version presents a continuous carbon surface across the tank flank. There are no openings for standard trim to show through, so the panel reads as one piece from the side.
That is the look most riders want when the goal is a clean carbon side profile rather than a mix of carbon and original plastics.
The trade-off is access. Anything that normally passes through or sits against that part of the tank has to be accounted for before the panel goes on. If your bike has a fixing, bracket, hose or trim piece in that area, check it against the panel before you commit.
What should you know about tank side panel with cutouts?
On the BMW S1000RR, the cutout version keeps openings in the panel. Those openings are there because something on the motorcycle needs the space: a fixing point, a hose route, a bracket, or a piece of standard trim that stays visible. With the cutouts, that hardware keeps working and the original part shows through the gap.
This is the version to choose when your bike is not completely standard in that area, or when you want to keep the factory detail visible instead of covering it. It is also the safer starting point if you are unsure, because the openings give you somewhere to route what is already there rather than forcing you to relocate it.

How do you tell which one your bike needs?
- Look at the tank flank on your own bike in daylight, with the seat off if that helps you see the edge of the panel.
- Note every opening, bracket, hose and trim line in that area. Photograph it straight on and from below.
- Compare that photo with the two product listings, side by side.
- If anything is unclear, send the photos with your model year before you order.
On the BMW S1000RR, do not decide from a photo of someone else's bike. Tank-area hardware changes with model year, market version and whatever the previous owner fitted. A 2019 bike and a 2024 bike are the same generation but not necessarily the same in the details.
What is the rest of the tank area?
On the BMW S1000RR, these side panels are one layer of a three-part area. Above them sits the S1000RR carbon tank cover, which runs over the top of the tank. Below and behind sits the smaller S1000RR small tank side panel.
If you are doing the whole flank, plan all three together so the panel gaps line up and the weave direction reads consistently.
Building one area at a time is fine. Just avoid buying the big panel last, because it sets the edges that the smaller pieces align to.
How do you install the tank side panels?
On the BMW S1000RR, fit the panel dry before you add any fastener. The tank flank curves in two directions, and a panel that is slightly off will look seated at the front and stand proud at the rear. If it needs force, something is trapped or the wrong version is in your hands.
- Work on a cold bike with the tank drained down or the fuel level low enough that you are not leaning on a full tank.
- Keep the original fasteners sorted by position; the two sides are not always identical.
- Start every fastener by hand, align the gaps, then tighten in a cross pattern.
- Stop at snug. Use your service literature for torque values rather than guessing.
- Recheck the panel edges after the first ride, especially if the bike has been apart before.
| Dimension | Notes |
|---|---|
| Platform | BMW S1000RR |
| Part | tank side panels |
| Install | No torque figures in this guide. Use the service manual and confirm the year on the product page. |
| Use | Street. |
| Shop | https://isleparts.com/products/bmw-s1000rr-carbon-fiber-full-coverage-tank-side-panels-2019-2024 |
What are the common questions?
On the BMW S1000RR, these are the usual questions. Are the two panels really the same price? Can I use the cutout panel and still get a clean look? Will these fit a 2025 S1000RR? Do I need both sides? Do they fit over crash sliders mounted at the tank?
Are the two panels really the same price?
Yes. The full-coverage tank side panels and the tank side panel with cutouts are both in this catalogue.
Can I use the cutout panel and still get a clean look?
Yes, if the openings line up with hardware you are keeping. The cutouts are visible, but they read as intentional when the part behind them is clean and correctly fitted.
Will these fit a 2025 S1000RR?
No. Both are listed for 2019-2024. The later bike uses different bodywork.
Do I need both sides?
Only if both sides are damaged or you are replacing the full set. Each listing shows a single default option, so confirm the quantity you need before checkout.
Do they fit over crash sliders mounted at the tank?
Assume not. Anything between panel and tank changes the fit — the cutout version is the only one that might accommodate existing hardware, and even then it needs the photo check first.
Compare the Full-coverage panels with the Cutout panel, or see the whole BMW S1000RR carbon fibre range.