Updated November 2026. Short answer: work from the bottom up. The lower chin fairing comes off first, then the side panels, then the shark fin insert, and the tank cover last if you need the top of the frame. Almost every broken tab on this bike comes from pulling a panel that is still captured at one hidden fastener.
Which order works?
- Lower chin fairing. It bridges the bottom of both side panels, so nothing above it will release cleanly while it is still fitted.
- Side panels. Release the rear edge first, then the front where it tucks behind the nose.
- Shark fin insert. It sits inside the side panel line and is often held partly by the panel you just removed.
- Tank cover. Only needed if you are chasing a leak, a loom, or fitting a new cover. It is not part of a routine side panel job.
The CF 675SR-R panel guide explains what each of these parts covers, which helps you decide how far to strip. Our 450SR removal guide covers the same discipline on the smaller bike if you work on both.
What should you know about tools you actually need?
On the CF 675SR-R, a trim tool or plastic wedge. Not a flathead screwdriver. The right hex and Torx sizes, in a socket or T-handle rather than a multitool. A tray or labelled bags for fasteners. This bike uses more than one length in the same panel line.
- A torch, because the lower fasteners are in shadow.
- Masking tape for the tank and the panel edges you are levering near.
What does the clips change?
On the CF 675SR-R, push-fit clips lose tension after a few removals and let the panel sit proud of its neighbour. If a clip spins in its seat or pulls out with the panel, replace it before refitting. Two habits save panels.
Warm the bike or the garage before working in cold weather, because cold ABS cracks instead of flexing. And when a panel resists, stop and look for a fastener you have missed rather than increasing force.
What does the side panel change?
On the CF 675SR-R, the side panel on this bike carries the mid-fairing line and covers the frame spar and part of the radiator duct. It is available in Gloss Black, Matte Black, Gray and White which means you can replace one damaged side rather than a set.
The675SR-R side panel fits the same mounting points as the original, so the removal order you use to take the old one off is the order you reverse to fit the new one.
What does the shark fin and chin change?
On the CF 675SR-R, the shark fin insert is a separate part from the side panel, not a moulded feature of it. It comes in Gloss Black, Matte Black and Gloss White and it is the panel most often scuffed in a low-speed drop because it sits proud of the side line.
Theshark fin side panel insert releases from inside the panel line, so fit the side panel loosely first, then the insert, then tighten both.
The lower chin fairing is the other low-cost part: Matte Black only, and it takes the road grit and the front tyre spray. The675SR-R lower chin fairing is worth keeping in stock if you ride through winter, because a cracked chin is cosmetic until it starts flapping.
What should you know about refitting without new rattles?
On the CF 675SR-R, start every fastener by hand and leave all of them loose until the panel is located in all its slots. Tighten from the centre of the panel outward, so the panel does not bow around a fixed point. Check the gap along the tank and the nose before final tightening.
- A panel that is tight at one end and proud at the other is usually one clip out of its seat.
- Do a short ride, then re-check every fastener. New panels settle in the first fifty miles.
| Dimension | Notes |
|---|---|
| Platform | CF 675SR-R |
| Part | CFMOTO fairing removal order |
| Install | Confirm the steps on the product page before you order. This guide does not add a torque sheet. |
| Use | Street. |
| Shop | https://isleparts.com/collections/cfmoto-675sr-r-675ss-parts |
What are the common questions?
On the CF 675SR-R, these are the usual questions. Do I have to remove the nose to take off a side panel? Can I ride with the chin fairing removed? Are the side panel and shark fin the same colour range? How long should this take?
Do I have to remove the nose to take off a side panel?
No. The side panel releases with the nose in place. Removing the nose only helps if you are replacing the front fairing or chasing a loom fault behind it.
Can I ride with the chin fairing removed?
Yes, temporarily, but the chin is what keeps spray off the lower engine and it stiffens the bottom edge of both side panels. Refit it before any distance.
Are the side panel and shark fin the same colour range?
Not exactly. The side panel comes in Gloss Black, Matte Black, Gray and White. The shark fin comes in Gloss Black, Matte Black and Gloss White. There is no Gray fin, so a Gray side panel pairs with a black or white insert.
How long should this take?
First time, an hour with a torch and a tray. Once you know the fastener layout, fifteen minutes per side.
All three parts live in the 675SR-R and 675SS parts collection.